Jump to content
  • Welcome to SEFP!

    Welcome!

    Welcome to our community forums, full of great discussions about Structural Engineering. Please register to become a part of our thriving group or login if you are already registered.

Concrete Design

Post any problems related to concrete design here. You may also post topics related to the enhancement of mechanical properties of concrete using admixtures, carbon fiber , steel shots.

260 topics in this forum

    • 1 reply
    • 96 views
  1. Shear wall design

    • 9 replies
    • 796 views
    • 5 replies
    • 165 views
    • 7 replies
    • 428 views
    • 2 replies
    • 147 views
    • 12 replies
    • 1,030 views
    • 10 replies
    • 192 views
    • 4 replies
    • 124 views
    • 15 replies
    • 8,106 views
  2. RCC Dome Design

    • 6 replies
    • 1,251 views
    • 2 replies
    • 336 views
    • 3 replies
    • 516 views
    • 9 replies
    • 214 views
    • 0 replies
    • 93 views
    • 3 replies
    • 1,132 views
    • 4 replies
    • 264 views
    • 1 reply
    • 104 views
    • 2 replies
    • 184 views
    • 2 replies
    • 105 views
    • 2 replies
    • 407 views
    • 2 replies
    • 210 views
    • 0 replies
    • 86 views
    • 2 replies
    • 155 views
    • 6 replies
    • 233 views
    • 0 replies
    • 86 views
  • Our picks

    • Dear Fellow Researchers, Academicians, and research students,

       

      NED University of Engineering & Technology in collaboration with Institution of Engineers Pakistan (IEP) is organizing 9th International Civil Engineering Conference (ICEC 2017) on December 22-23, 2017 at Karachi, Pakistan.

       The congress details are available at its website www.neduet.edu.pk/icec

       Also attached is congress flyer for information and dissemination among your peers.

       Abstracts submission deadline has been extended till October 31, 2017.

      Please click on the link to see the full description.
      • 0 replies
    • AoA all,

      Is it mandatory to do column concreting upto the soffit of the beam in a single pour ?

      What code says about the construction/cold joint location in column ?

      Majority of the contractors are pouring the column concrete upto the soffit of the beam (full height of the column), some contractors leave the column height about 9" to 12" below the beam level and then fill this 9" to 12" column height with the beams & slab concreting. On one site column concreting was stopped at the mid height and the remaining half was filled on the next day.

      Thanks

       

       
      • 5 replies
    • AOA 

      i am facing problems in shear wall design .what are the pier and spandral ?what will be the difference when we assign pier or spandral? without assigning these the shear wall design is incomplete .

      i am taking about etabsv16

      someone have document about shear wall design plz provide it 

      thank you

       
      • 9 replies
    • Salam Members,

      Congratulations to Engineers, PEC has become full signatory of Washington Accord, what are the benefits to Pakistani engineers for this agreement. 

       

      Regards   

       

       
      • 3 replies
    • Please clarify the following confusions one by one:-

       

      1. If we run P-delta analysis in ETABS, then should we ignore stiffness property modifiers for beams and columns? I have heard that if we perform P-delta analysis and apply stiffness modifiers at the same time then the moment magnification process is doubled...?

       

      2. ETABS considers selenderness of a column by applying moment magnification factors. If we run P-delta analysis also, does it mean that the selenderness of column is being over-estimated? I mean once the moments are magnified in P-delta analysis process and again through moment magnification process?

       

      Please help me understand the software myth and clarify above confusions.
      • 1 reply
  • Recently Browsing   0 members

    No registered users viewing this page.

×

Important Information

By using this site, you agree to our Terms of Use and Guidelines.